Dissolved oxygen meter  SX716 DO Meter

Technical Parameters:

1.     Dissolved Oxygen:

Measuring range：(0 to 40.00) mg/L(ppm)  (0 to 200.0) %

Resolution：0.1/0.01 mg/L(ppm)  1/0.1%

Accuracy：Meter:±0.10 mg/L, connect meter with electrode:±0.40 mg/L

Response time：≤30 s (25℃, 90% response)

Residual current：≤0.1 mg/L

Temp. compensation range：(0 to 45) ℃ (automatic)

Salinity compensation range：(0 to 45) ppt (automatic)

Barometric pressure compensation range：(66 to 200) kPa (manual)

Automatic calibration：Air saturated by water; water saturated by air

Electrode type：Polarogram type

2.     Other Technical Parameters:

D ata storage：100 groups

Storage content：Series number, measuring value measuring unit and temperature

Power：Two AA batteries (1.5V x2)

Size and weight：Meter: (65×120×31)mm/180g Carrying case:(255 x210x 50)mm/790g

Quality and safety certification：ISO9001:2000, CE and CMC

3.     Working Condition:

Environment temperature：5 to 35 ℃ (0.01 grade)

Environmental humidity：≤85%

IP rating：IP57 Dustproof and waterproof

Meter’s Complete Kit:

2.1. Model SX716 DO meter

2.2. DO500 DO electrode

2.3. DO503 membrane cap (DO electrode use)

2.4. DO502 DO electrode inner solution (30mL)

2.5. Cathode polishing paper

2.6. Screw driver

2.7. Spare AA batteries

2.8. Operation manual

2.9. Brief operation instruction

2.10. Packing list

2.11. Carrying case

Portable Dissolved Oxygen Meter  JPBJ-607 D. O. Analyzer

Specification
Range: 0.00~19.99mg/L 　0.0~255.0%
Resolution: 0.01mg/L 　0.1%
Accuracy: ±1.5%F.S
Temperature Compensation: 0~45℃
Power Supply: DC 9V
Dimensions: 123mm×72mm×33mm
Dissolved oxygen meter 
1. general
2. specifications
3. structure of the meter
4. operation and calibration
5. maintenance
6. appendix
 
1. General
It’s a portable instruments designed for using at work site. It can measure dissolved oxygen measurement and temperature.
 
2. Specification
2.1 measuring range: (0.00-20.0) mg/L Temperature: (0.0-40.0)℃
2.2 automatic temperature range: (0.0-40.0)℃
2.3 accuracy of electric unit: + 0.1mg/L + 1bit
2.4 Accuracy:
Dissolved oxygen:
 +0.1mg.L-1 (at same calibration and measuring temperature)
+0.5mg.L-1 (at +10℃ difference between calibration and measuring temperature)
Temperature: +1℃
 
2.5 electronic unit stability: 0.1mg/L + 1 bit within 3 hour.
2.6 Stability of the meter: 0.2mg/L + 1 within 1 hour
2.7 Response time: not more than 30 seconds( at 20℃, 90% response)
2.8 Residual current: not more than 0.15mg/L + 1
2.9 Working environment:
Ambient temperature: (0.0-40.0)℃
Relative humidity: not more that 85%
Temperature of samples to be measured: (0.0-40.0)℃
Power supply: AA battery
No obvious electromagnetic interference except terrestrial magnetic fields.
Size: 165x 75 x 30 mm
net Weight: 0.3kg
gross weight: 3kg
3. structure:
3.1 structure of instruments
 
1. display screen
2. electrode socket
3. back light screen button
4. power on/ off
5. mode key
press this key, you can switch to “dissolved oxygen measure/zero oxygen calibration/span calibration/salinity setting.
6. set key
press this key to store the value when it is at /zero oxygen calibration/span calibration/salinity setting.
 7. ↑key 8. ↓key adjust the salinity value when it is working at salinity setting.
9.electrode
When it shows “LOBAT” on screen, you should change battery.
3.2 electrode
 
1. screw, connect to electrode socket
2. oxygen electrode.
 
4. operation and calibration
 1. put into the battery.
2. press power key, the instruments can start working automaticly, there’s four mode of working.
You can switch the working mode by # 5 mode key .
When it shows:
　
It is measuring dissolved oxygen.
Remarks: when the electrode is not connected, or the temperature electrode doesn’t work, the insruments will show 25℃, the dissolved oxygen will be measured as 25℃
If it is the first time to use it, or you havn’t used it for quite a long time, you should calibrate the electrode according to charper No.4.3
 4.3 calibration.
New electrode, electrode that not used for over 24 hours,when new solution is installed, the electrode need to be polarized for 30-60 minutes,
When electrode left the instruments, or the instrument is off for 1 hour,the electrode should be polarizedfor 5—25 minutes.
4.3.1
Zero oxygen calibration
Put the dissolved oxygen electrode into newly made 5% sodium sulphate solution, when the instruments is in the mode of measure dissolved oxygen, press mode key switch to zero oxygen calibration, store the value when the reading is stable.
For zero calibration, it will shows this in screen:
　
Then finish zero calibration, press mode key again switch to full calibration.
Get out the electrode from the solution, clean it with water and dry it with clean paper. Put the electrode over the surface of stilled water, but not contact the water.
Press set key to store the value when the reading is stable. full calibration finish.
Screen is as follows when setting full calibration.
 
Press mode key again to switch to salinity setting.
Default salinity value is 0.00, choose a right salinity value before measure dissolved oxygen. You can set the salinity value by pressing key# 7, key # 8.
 5. maintenance
The dissolved oxygen electrode should be stored in distilled water. DO NOT put it into the sodium sulphate solution. 

Dissolved oxygen meter model: JPBJ-608 D. O. Analyzer

Characteristics:
1. With the function of double displays of dissolved oxygen concentration value and temperature, dissolved oxygen saturation value and temperature
2.Measuring D.O. concentration, saturation, electrode current and temperature; With the functions of automatic temperature compensation and calibration of zero oxygen, full scale, atmosphere pressure and salinity.
3.The meter has the function of protection from electricity cutting off. With Measuring results can be stored, deleted, viewed and printed. At most 250 sets of data can be stored.
4. With wide screen LCD. It is easy to operate with the prompt facility. With PC panel of new material, thus the meter has good reliability.
5. With low power consumption design, with the functions of lack of voltage display, switching off automatically.
6.With RS-232 interface which is connected and with Model TP-16 printer to print measuring results or connected with computer to communicate.
7.Grade of the case protection is IP65, resistant to water and dirt, suitable for field operation
8.The electrode system is composed of polarographic oxygen electrode and temperature electrode.

Specifications
1.Measuring range: Dissolved oxygen concentration: (0.00~19.99)mg/L
Dissolved oxygen saturation: (0.0~199.9)%;
Temperature: (0~40.0)℃.
2.Automatic temperature compensation range: (0.0~40.0) ℃.
3.Accuracy of the meter: D.O. concentration: ±0.3mg/L±1bit(under basic temperature);
±0.5mg/L (differ: ±15°C from the basic temperature)
D.O. saturation : ±5.0% (under basic temperature);
±10.0% differ: ±15°C from the basic temperature
Temperature: ±0.5℃±1bit.
4.Repeatability of the meter: ≤0.2mg/L.
5.Stability of the meter: not over ±0.2mg/L within one hour.
6.Remaining current: ≤0.1mg/L.
7.Response time ≤20s (90% response at 20.0℃).
8.Salinity calibrating range: (0.0~40.0)g/L.
9.IP65 protection grading

Oxygen analyzers with alarm

Measuring range: 0—100%, 0-25%, and 0-1%

This gauge have three kind of range, you can select one range according to conditions.

Accuracy:  +0.1%

Large LED screen

Power supply: 6V battery, can work continuously for 300 hours.

Size: 200x95x35 mm

Weight :  150g.

Alarm range: can be set manually. For example, if you select 10—30%, then the alarm will make voice when the oxygen is under 10% or over 30%

Resolution: 0.01%

Can be used in mining, ship, chemical, educational, environmental pharmaceutical field